F6-N20 Non-Slip Flat Stair Nosing
Ecoglo®’s F6-N20 Non-Slip Anodized Stair Nosing is one of the most cost-effective ways to renovate and modernize your facility, while increasing the safety of stairwells. This product provides anti-slip protection, thanks to the integrally bonded N Series Non-Slip strip, as well as ridges in the aluminum. Our aluminum stair nosing further adds to the safety of your facility by providing clear step-edge visibility. The stark color contrast of our non-slip stair nosing clearly marks the stair tread, allowing patrons to safely ascend or descend the stairways in your building.
To better fit the needs of your facility, Ecoglo®’s non-slip anodized stair nosing can be permanently installed on a variety of substrates including concrete, timber, tiles, steel, checker plate and thin carpet.
Downloads:
General Information
- Install with polyurethane adhesive and mechanical fasteners, or adhesive only.
- Supplied with pre-drilled countersunk holes. Includes stainless steel fasteners and concrete nylon anchors. Standard location is 2″ from each end and approx. 12″ apart.
- Available in cut to length sizes. (Tolerance +or- 1/8”) Standard lengths are 8ft and 10ft.
- Inserts Attached or Unattached – Unattached is recommended for on-site cutting. Inserts are installed with a premium polyurethane adhesive.
- Weight: 0.482 lbs/ft.
Aluminum Finish:
- Available in Clear Anodized Aluminum Finish.
- Black, Light Bronze and, Dark Bronze Anodize finishes are available at an additional cost.
- The hard-wearing silicon carbide non-slip material is integrally bonded to the aluminum substrate. Thousands of people can walk on it with no signs of wear and tear.
- The thick anodized finish is aesthetically pleasing, prevents corrosion, and is extremely hard and abrasion resistant. The anodized aluminum surface is harder than pure aluminum, second only to diamonds hard crystalline structure.
- The color contrasting the non-slip material provides excellent step edge visibility
- Tested to accelerated UV/Weathering Exposure, Salt Spray Resistance, Freeze Thaw Resistance and Washability. Ecoglo® products easily passed with excellent results.
- LEED points qualified
- Recyclable; No disposable cost
Photos
Leed Data
- Products are Aluminum based and 100% recyclable.
MR Credit 4: Recycled Content
- Products are Aluminum based and approximately 20% of the aluminum content in an Ecoglo secondary billet specification is recycled scrap.
Ecoglo’s Recommended Installation Adhesive has low VOC’s and qualifies for Indoor Environmental Quality credits for low emitting materials: EQc4.1
Benefits And Technical Data
Ecoglo F6-N20 meets or exceeds the performance criteria specified in the following tests or standards:
High durability indoors and outdoors.
- ASTM G155-04 Cycle 1 2000hrs, Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Nonmetallic Materials.
- Salt Spray Resistance: ASTM B117-97 500hrs, Standard Practice for Operating Salt Spray (Fog) Apparatus.
- Freeze-Thaw Resistance: ASTM C1026-87(1996) Standard Test Method for Measuring the Resistance of Ceramic Tile to Freeze-Thaw Cycling
- ASTM D1242-95a, Standard Test Methods for Resistance of Plastic Materials to Abrasion.
- ASTM B 244-97, Test Methods for Measurement of Anodic Coatings on Aluminum and other Nonconductive Coatings on Nonmagnetic Basis Metals with Eddy-Current Instruments.
- ASTM B137-95(2000), Test Method for Measurement of Coating Mass per Unit Area of Anodically Coated Aluminum.
- ASTM F510-93(2004), Standard Test Method for Resistance to Abrasion of Resilient Floor Coverings Using an Abrader with a Grit Feed Method.
- JIS H8682-1:1999, Test methods for abrasion resistance of anodic oxide coatings on aluminum and aluminum alloys- Wheel wear test.
- ASTM D4828-94(2003), Standard Test Methods for Practical Washability of Organic Coatings.
- ASTM B136-84(1998), Standard Test Method for Measurement of Stain Resistance of Anodic Coatings on Aluminum.
Reduces Slips
- UL410 Standard for Slip Resistance of Floor Surface Materials
- AS/NZS 4586 Slip Resistance Classification of New Pedestrian Surface Materials.
Does not burn.
- ASTM E162-16 Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source.
- ASTM D635-18 Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position.
- FAA AC 23.2 Paragraph 4.b, Horizontal Burn Test.